This page is for v0.10, not the latest stable version which is v0.12. For the latest stable version of this article, click here.
forward Output Plugin
out_forward Buffered Output plugin forwards events to other fluentd nodes. This plugin supports load-balancing and automatic fail-over (a.k.a. active-active backup). For replication, please use the out_copy plugin.
out_forward plugin detects server faults using a “φ accrual failure detector” algorithm. You can customize the parameters of the algorithm. When a server fault recovers, the plugin makes the server available automatically after a few seconds.
|Do NOT use this plugin for inter-DC or public internet data transfer without secure connections. All the data is not encrypted, and this plugin is not designed for high-latency network environment. If you require a secure connection between nodes, please consider using in_secure_forward.|
Table of Contents
- Example Configuration
- type (required)
- <server> (at least one is required)
- <secondary> (optional)
- Buffered Output Parameters
- buffer_queue_limit, buffer_chunk_limit
- retry_wait, max_retry_wait
- retry_limit, disable_retry_limit
out_forward is included in Fluentd’s core. No additional installation process is required.
<match pattern> type forward send_timeout 60s recover_wait 10s heartbeat_interval 1s phi_threshold 16 hard_timeout 60s <server> name myserver1 host 192.168.1.3 port 24224 weight 60 </server> <server> name myserver2 host 192.168.1.4 port 24224 weight 60 </server> ... <secondary> type file path /var/log/fluent/forward-failed </secondary> </match>
|Please see the Config File article for the basic structure and syntax of the configuration file.|
The value must be
<server> (at least one is required)
The destination servers. Each server must have following information.
- name: The name of the server. This parameter is used in error messages.
- host (required): The IP address or host name of the server.
- port: The port number of the host. The default is 24224. Note that both TCP packets (event stream) and UDP packets (heartbeat message) are sent to this port.
- weight: The load balancing weight. If the weight of one server is 20 and the weight of the other server is 30, events are sent in a 2:3 ratio. The default weight is 60.
The backup destination that is used when all servers are unavailable.
The timeout time when sending event logs. The default is 60 seconds.
The wait time before accepting a server fault recovery. The default is 10 seconds.
The transport protocol to use for heartbeats. The default is “udp”, but you can select “tcp” as well.
The interval of the heartbeat packer. The default is 1 second.
Use the “Phi accrual failure detector” to detect server failure. The default value is
The threshold parameter used to detect server faults. The default value is 16.
The hard timeout used to detect server failure. The default value is equal to the send_timeout parameter.
Marks a node as the standby node for an Active-Standby model between Fluentd nodes. When an active node goes down, the standby node is promoted to an active node. The standby node is not used by the
out_forward plugin until then.
<match pattern> type forward ... <server> name myserver1 host 192.168.1.3 weight 60 </server> <server> # forward doesn't use myserver2 until myserver1 goes down name myserver2 host 192.168.1.4 weight 60 standby </server> ... </match>
Buffered Output Parameters
For advanced usage, you can tune Fluentd’s internal buffering mechanism with these parameters.
The length of the chunk queue and the size of each chunk, respectively. Please see the Buffer Plugin Overview article for the basic buffer structure. The default values are 64 and 8m, respectively. The suffixes “k” (KB), “m” (MB), and “g” (GB) can be used for buffer_chunk_limit.
The interval between data flushes. The default is 60s. The suffixes “s” (seconds), “m” (minutes), and “h” (hours) can be used.
If set to true, Fluentd waits for the buffer to flush at shutdown. By default, it is set to true for Memory Buffer and false for File Buffer.
The initial and maximum intervals between write retries. The default values are 1.0 seconds and unset (no limit). The interval doubles (with +/-12.5% randomness) every retry until
max_retry_wait is reached. In the default configuration the last retry waits for approximately 131072 sec, roughly 36 hours.
The limit on the number of retries before buffered data is discarded, and an
option to disable that limit (if true, the value of
retry_limit is ignored and
there is no limit). The default values are 17 and false (not disabled). If the limit is reached, buffered data is discarded and the retry interval is reset to its initial value (
The number of threads to flush the buffer. This option can be used to parallelize writes into the output(s) designated by the output plugin. Increasing the number of threads improves the flush throughput to hide write / network latency. The default is 1.
log_level option allows the user to set different levels of logging for each plugin. The supported log levels are:
Please see the logging article for further details.
“no nodes are available”
Please make sure that you can communicate with port 24224 using not only TCP, but also UDP. These commands will be useful for checking the network configuration.
$ telnet host 24224 $ nmap -p 24224 -sU host
Please note that there is one known issue where VMware will occasionally lose small UDP packets used for heartbeat.
If this article is incorrect or outdated, or omits critical information, please let us know. Fluentd is a open source project under Cloud Native Computing Foundation (CNCF), originally invented by Treasure Data, Inc. All components are available under the Apache 2 License.